See our wide range of Geotechnical and Structural sensors
The W1 Standpipe Piezometer is a reliable and cost-effective Casagrande type piezometer designed for monitoring in vertical boreholes. At Monitel, we have used it to measure groundwater levels and pore water pressures on sites across Western Australia.
The sensor is typically installed with the filter tip positioned at the chosen monitoring depth. For pressure data, the tip is surrounded by sand and enclosed with a bentonite seal to isolate the measurement area. Water level data can be gathered through a riser pipe or a Bourdon gauge (in artesian conditions). The W1 is suitable for various ground types and can be customised to match specific site requirements. It can be deployed with either a porous or ceramic tip and has a drive-in capacity for softer soils. The simplicity, versatility and reliability of the W1 Standpipe Piezometer make it an ideal choice for an accurate and consistent groundwater monitoring solution. Key Specifications:The 4-20mA Piezometer is engineered to precisely measure pore water pressure in fully or partially saturated soil and rock. It is one of the more commonly deployed sensors in our piezometer range.
It utilises a diaphragm-type pressure transducer, delivering a robust 4-20mA output signal that is ideal for integration with data loggers and remote monitoring systems. It boasts an advanced and durable design, with 316-grade stainless steel and hermetic sealing protecting the technology from environmental effects. The casing itself is constructed to ensure that any stresses have no impact on readings. The 4-20mA is capable of measuring pressures from -50 kPa to 3500 kPa, accommodating a wide range of monitoring needs. Key specifications:The W16 Kompakt Piezometer is a vibrating wire piezometer designed for fast and accurate measurement of pore water pressures.
It utilises proven vibrating wire technology, where changes in wire tension correlate to changes in pore water pressure. Data is then sent to a read-out, terminal unit or data logger. The W16 boasts a compact design, making it ideal for confined installations. It is only 19mm in diameter and weighs just 150g (excluding the filter and cable). However, it is also robust and durable, with hermetic sealing promoting resistance to environmental factors. An over-voltage surge arrestor safeguards against electrical damage. The sensor tip includes an integral porous element, which houses the vibrating wire technology. Key Specifications:The VWP-3000 Series Vibrating Wire Piezometers are designed to provide measurements of pore water pressure across geotechnical and structural engineering applications.
These piezometers work by converting fluid pressures (exerted on a sensitive diaphragm) into a frequency signal. They collect reliable and accurate data suitable for monitoring groundwater elevations, pore pressures and fluid pressures.The series is built to withstand tough and demanding conditions, ideal for direct burial in fills, embankments and boreholes. Each model includes an internal thermistor and a 90V gas plasma arrester, acting as a safeguard against lightning strikes.
The VWP-3000 Series also features:
Models in the VWP-3000 Series:
Made in Australia, the Viotel Wireless Triaxial Tiltmeter (VWTT) is a pre-programmed, ready to mount monitoring device designed to detect and measure angular movements across three axes.
Encased in a durable, UV-stabilised ABS plastic housing, it performs reliably in harsh and diverse environmental conditions. It is entirely self contained, with an internal battery, GPS and cellular CAT-M1 modem all held within the casing.
The VWTT provides high-precision data, working at a resolution of of 0.0003° and an accuracy of 0.001°. Readings are taken at pre-determined intervals that you can configure on the myViotel platform.
Installation can be completed with 3M adhesive backing, 2 bolt holes or a pole mount. This allows versatile deployment suited to your preferred location and orientation.
Event Detection Mode:
The VWTT’s Event Detection Mode enables continuous tilt monitoring every 4 seconds, automatically triggering an alert when movements exceed your pre-set thresholds. This means that structural shifts are detected almost immediately.
Capturing real-time movement data and transmitting alerts via the myViotel platform, this feature allows for rapid response to potential stability risks, helping prevent structural failures and ensuring site safety.
Specifications:
The Viotel Accelerometer is a wireless sensor designed for real-time vibration and acceleration monitoring in geotechnical and structural applications. This compact, battery-powered device provides continuous measurement of ground and structural movement, making it ideal for monitoring bridges, tunnels, dams, buildings and mining operations.
Equipped with triaxial acceleration sensors, the Viotel Accelerometer captures vibration data across three axes, allowing for detailed analysis of structural responses to environmental and operational loads. It offers high sampling rates and low-power consumption, allowing for long-term deployment without frequent maintenance. The wireless connectivity enables seamless data transmission to Viotel’s cloud-based monitoring platform, providing real-time alerts and remote access to data. The system allows engineers to track changes in structural behavior, detect anomalies and intervene to prevent failures. Designed for easy deployment, the Viotel Accelerometer supports automated data logging and integration with existing structural monitoring systems, making it a cost-effective solution for projects requiring continuous vibration monitoring. Its rugged construction ensures durability in harsh environments, delivering precise, actionable insights for infrastructure and asset management.The VWS-2000 Surface-Mount Vibrating Wire Strain Gauge is a high-precision sensor designed to measure strain in structural and geotechnical applications. Using vibrating wire technology, it provides accurate, long-term strain monitoring for a wide range of materials, including steel, concrete and rock. This sensor is commonly used in monitoring bridges, retaining walls, dams and structural beams, allowing engineers to assess load distribution, stress changes and structural integrity over time.
The VWS-2000 consists of a robust stainless steel body with mounting brackets for secure attachment to surfaces. The gauge measures strain by detecting frequency shifts in the vibrating wire, ensuring high accuracy, stability and resistance to temperature fluctuations. With a gauge length of 150 mm, it captures precise strain measurements while maintaining durability in harsh environments. This strain gauge is compatible with automated data logging systems, enabling real-time monitoring and remote access to data. Its low-maintenance design ensures long-term performance, making it ideal for critical infrastructure projects.